Tools You Need to Set Up a New Tub
Tools You Need to Set Up a New Tub
Blog Article
How do you actually feel about Installing A Bathtub?
Installing a bath tub isn't precisely rocket science, yet it does require strong plumbing, carpentry, and occasionally, tiling skills. Changing an old tub with a new one is likewise a reasonably tough project. If the old bathtub is readily available, the job can move immediately; if you need to open a wall surface to eliminate the old bathtub as well as position the brand-new bathtub, the job is much harder. In either instance, the project is within a residence handyman's skills, although you will require a helper to leave the old tub and also set in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable trying it. Rather than working with a professional to take control of a halfway-completed project, it is much better to take into consideration utilizing one prior to you begin. Opportunities are you might need a professional plumber to make tube links.
This article will certainly help you set up a new bath tub in your restroom if you have actually already acquired a new bathtub and do not need to transform the plan of your previous water pipes.
Your devices and product checklist must comprise the following:
Planning for the Installation
First of all, the supporting framework provided with the bath must be fitted (if called for) according to the producer's instructions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is important to make certain that if the faucet includes a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the faucets unit to avoid pressure on the bathtub.
Fit the versatile faucet connectors to the bottom of the two taps making use of 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the water supply. After doing so, turn on the faucets to drain pipes any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic due to the limited gain access to that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipes have been removed, use the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Installing the Bathtub
Using both wood boards under its feet, put the bathtub in the required placement. The wood boards are valuable in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the spirit level and readjusting the feet on the tub up until the spirit level reviews level.
To install faucets, fit the bottom of the furthest adaptable faucet connector to the ideal supply pipeline by making a compression sign up with; after that do the same for the various other faucet.
Switch on the water as well as check all joints and also new pipework for leaks and also tighten them if required. Load the bathtub as well as also examine the overflow outlet and also the normal electrical outlet for leaks.
Lastly, fix the bathroom paneling as described in the maker's user's manual. Tiling as well as securing around the bathtub must wait until the tub has actually been utilized at the very least once as this will certainly resolve it into its last position.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap as well as the sink. Safeguard the tap in position with the manufacturer offered backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with normal tap ports. The previous type must be attached to the tap ends initially, tightening only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture a rigid seal, triggering the water to permeate the wall surface in between the bath and the tiling, causing issues with moisture and also feasible leaks to the ceiling below.
You can choose from a range of coloured sealers to assimilate your components and also fittings. They are sold in tubes and also cartridges, and are capable of sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before sealing, to allow for the motion experienced when the tub is in use. The sealant can split relatively very early if you do not think about this motion prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are likewise quickly offered on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I have been very enthusiastic about How to Install a Bathtub and I hope you enjoyed the piece. Those who enjoyed reading our article plz remember to pass it around. Thanks a bunch for your time. Come back soon.
Visit Our Site
Report this page